Ripper
Pry-Out Force
25972 lb 11780.8 kg
Penetration Force
18911 lb 8577.9 kg
Machine Length Increase, Beam Raised
39.2 in 995.7 mm
Engine
Net Power Gear 4-6
173 hp 129 kw
Engine Model
C6.6 ACERT VHP C6.6 ACERT VHP
Frame
Front Frame Structure - Height
0.9 ft in 254 mm
Front Frame Structure - Width
0.9 ft in 254 mm
Front Frame Structure - Thickness
0.1 ft in 16.1 mm
Engine
Net Power Gear 1-2
163 hp 121 kw
Power Measured @
2000 rpm 2000 rpm
Net Power Gear 5-6
173 hp 129 kw
Max Power
173 hp 129.1 kw
Net Power Gears 7-8
173 hp 129 kw
Displacement
403 cu in 6.7 L
Engine Model
Cat C6.6 ACERT VHP Cat C6.6 ACERT VHP
Derating Altitude
11500 ft in 3505.2 m
Maximum Torque
690 lb ft 935.6 Nm
Base Power (1st Gear) - Net
158 hp 117.9 kw
Speed At Rated Power
2000 RPM 2000 RPM
High - Ambient Capability
122 degrees 122 degrees
High Ambient - Fan Speed - Maximum
1650 RPM 1650 RPM
High Ambient - Fan Speed - Minimum
550 RPM 550 RPM
Vhp Plus Range - Net
118-144 kW (158-193 hp) 118-144 kW (158-193 hp)
Frame
Circle - Diameter
60.2 in 1529.1 mm
Drawbar - Height
6 in 152.4 mm
Front Axle - Height To Center
22.5 in 571.5 mm
Circle - Blade Beam Thickness
1.4 in 35.6 mm
Front Axle - Total Oscillation Per Side
32 degrees 32 degrees
Drawbar - Thickness
0.4 in 10.2 mm
Drawbar - Width
3 in 76.2 mm
Front Axle - Wheel Lean - Left/Right
18 degrees 18 degrees
Engine
Torque Rise - Vhp Plus
40% 40%
Base Power (All Gears) - Net
158 hp 117.9 kw
Standard - Fan Speed - Maximum
1150 RPM 1150 RPM
Standard - Fan Speed - Minimum
550 RPM 550 RPM
Standard - Ambient Capability
109 degrees 109 degrees
Vhp Range - Net
118 -129 kW (158-173 hp) 118 -129 kW (158-173 hp)
Frame
Drawbar - Yoke Bar Thickness
0.8 in 19.1 mm
Operational
Std Operation Weight - Front Axle
8836 lb 4008 kg
Std Operation Weight - Rear Axle
23180 lb 10514 kg
Hydraulic System Fluid Capacity
16 gal 60 L
Std Operation Weight - Total
32016 lb 14522 kg
Max Operation Weight - Front Axle
15284 lb 6933 kg
Max Operation Weight - Rear Axle
29406 lb 13338 kg
Max Operation Weight - Total
44690 lb 20271 kg
Fuel Capacity
90 gal 340 L
Cooling System Fluid Capacity
10.4 gal 40 L
Rear Diff/Final Drive Fluid Capacity
13.2 gal 50 L
Circle Gearbox Fluid Capacity
1.8 gal 7 L
Tandem Case Fluid Capacity (Each)
16.9 gal 61 L
Power Train
Brakes - Parking
Multiple oil disc Multiple oil disc
Brakes - Service
Multiple oil-disc Multiple oil-disc
Transmission
Direct drive, power shift, countershaft Direct drive, power shift, countershaft
Forward/Reverse Gears
8 Fwd / 6 Rev 8 Fwd / 6 Rev
Brakes - Secondary
Dual circuit control system Dual circuit control system
Brakes - Service - Surface Area
3565 in2 2.3 m2
Steering
Articulation Angle
20 degrees 20 degrees
Turning Radius
24.5 ft in 7.5 m
Transmission
Transmission Type
direct drive, power shift, countershaft direct drive, power shift, countershaft
Number Of Gears - Forward
8 8
Number Of Gears - Reverse
6 6
Max Speed - Forward
27.7 mph 44.5 km/h
Max Speed - Reverse
23.5 mph 37.8 km/h
Front Axle
Wheel Lean
18 degrees 18 degrees
Oscillation - Total
32 degrees 32 degrees
Ground Clearance
1.9 ft in 572 mm
Weights
Gross Vehicle Weight - Base - Total
33064 lb 14997.6 kg
Gross Vehicle Weight - Maximum - Total
44690 lb 20271.1 kg
Gross Vehicle Weight - Base - Rear Axle
23145 lb 10498.4 kg
Gross Vehicle Weight - Base - Front Axle
9919 lb 4499.2 kg
Gross Vehicle Weight - Maximum - Front Axle
15954 lb 7236.7 kg
Gross Vehicle Weight - Maximum - Rear Axle
48736 lb 22106.3 kg
Hydraulic System
Standby Pressure
450 psi 450 psi
Maximum System Pressure
3500 psi 3500 psi
Moldboard
Moldboard Width
12 ft in 3668 mm
Moldboard Height
24 in 609.6 mm
Moldboard Thickness
0.9 in 22 mm
Max Depth Of Cut
28.3 in 720 mm
Side Shift Left
20.1 in 510 mm
Side Shift Right
26 in 660 mm
Blade Pull At Max Weight
26465 lb 12004 kg
Blade Down Pressure
27066.2 lb 12277 kg
Hydraulic System
Pump Type
Variable piston Variable piston
Pump Flow
51 gal/min 193 L/min
Relief Valve Pressure
3500 psi 24100 kPa
Circuit Type
Electro-hydraulic closed center, load sensing, Electro-hydraulic closed center, load sensing,
Pump Output
51 gal/min 51 gal/min
Moldboard
Blade Width
12 ft in 3.7 m
Arc Radius
16.3 in 414.1 mm
Throat Clearance
4.9 in 124 mm
Cutting Edge Width
6 in 152.4 mm
Cutting Edge Thickness
0.6 in 15.3 mm
End Bit - Width
6 in 152.4 mm
End Bit - Thickness
0.6 in 15.3 mm
Moldboard - Height
24 in 609.6 mm
Moldboard - Thickness
0.9 in 22.1 mm
Blade Pull - Maximum Gvw
25862 lb 11730.9 kg
Blade Pull - Base Gvw
20830 lb 9448.4 kg
Blade Down Pressure - Base Gvw
17566 lb 7967.9 kg
Blade Down Pressure - Maximum Gvw
28254 lb 12815.8 kg
Circle
Shift Left
25.8 in 656 mm
Shift Right
25.8 in 656 mm
Max Reach Outside Tires - Left
68.6 in 1742 mm
Max Reach Outside Tires - Right
75 in 1905 mm
Max Lift Above Ground
16.8 in 427 mm
Blade Tip Angle - Front
40 degrees 40 degrees
Blade Tip Angle - Rear
5 degrees 5 degrees
Operating Specifications
Top Speed - Forward
27.7 mph 44.6 km/h
Top Speed - Reverse
23.5 mph 37.9 km/h
Turning Radius - Outside Front Tires
24.5 ft in 7.5 m
Steering Range - Left/Right
47.5 degrees 47.5 degrees
Articulation Angle - Left/Right
20 degrees 20 degrees
Forward - 8th
27.7 mph 44.6 km/h
Forward - 7th
19 mph 30.6 km/h
Forward - 6th
13.8 mph 22.3 km/h
Forward - 5th
10.2 mph 16.5 km/h
Forward - 4th
6.5 mph 10.5 km/h
Forward - 3rd
4.8 mph 7.7 km/h
Forward - 2nd
3.3 mph 5.4 km/h
Forward - 1st
2.4 mph 3.9 km/h
Reverse - 6th
23.5 mph 37.9 km/h
Reverse - 5th
16.1 mph 26 km/h
Reverse - 4th
8.6 mph 13.9 km/h
Reverse - 3rd
5.6 mph 9.1 km/h
Reverse - 2nd
3.8 mph 6.2 km/h
Reverse - 1st
2 mph 3.3 km/h
Standards
Brakes
ISO 3450:1996 ISO 3450:1996
Rops/Fops
ISO 3471:1992 / ISO 3449:1992 ISO 3471:1992 / ISO 3449:1992
Sound
ISO 6394:1998 / ISO 6395:1988 ISO 6394:1998 / ISO 6395:1988
Steering
ISO 5010:1992 ISO 5010:1992
Service Refill
Cooling System
10.4 gal 39.4 L
Engine Oil
4.1 gal 15.6 L
Hydraulic System - Tank
16 gal 60.6 L
Tandem Housing - Each
16.9 gal 64 L
Circle Drive Housing
1.8 gal 6.9 L
Front Wheel Spindle Bearing Housing
0.1 gal 0.4 L
Fuel Capacity
90 gal 340.7 L
Transmission - Differential - Final Drives
13.2 gal 50 L
Blade Range
Circle Centershift - Right
25.8 in 655.4 mm
Circle Centershift - Left
25.8 in 655.4 mm
Moldboard Sideshift - Right
26 in 660.4 mm
Moldboard Sideshift - Left
20.1 in 510.6 mm
Blade Tip Range - Forward
40 degrees 40 degrees
Blade Tip Range - Backward
5 degrees 5 degrees
Maximum Shoulder Reach Outside Of Tires - Right
75 in 1905 mm
Maximum Shoulder Reach Outside Of Tires - Left
68.6 in 1742.5 mm
Maximum Lift Above Ground
16.8 in 426.8 mm
Maximum Depth Of Cut
28.3 in 718.9 mm
Maximum Blade Position Angle
90 degrees 90 degrees
Scarifier
Rear - Scarifier Shank Holders
9 9
Mid, V-Type - Scarifier Shank Holders
11 11
Front, V-Type, 5 Or 11 Tooth - Working Width
47.4 in 1204 mm
Front, V-Type, 5 Or 11 Tooth - Scarifying Depth, Maximum
18.4 in 467.4 mm
Front, V-Type, 5 Or 11 Tooth - Scarifier Shank Holders
5 / 11 5 / 11
Front, V-Type, 5 Or 11 Tooth - Scarifier Shank Holder Spacing
4.6 in 116.9 mm
Mid, V-Type - Working Width
46.6 in 1183.7 mm
Mid, V-Type - Scarifying Depth, Maximum
11.5 in 292.1 mm
Mid, V-Type - Scarifier Shank Holder Spacing
4.6 in 116.9 mm
Rear - Working Width
91 in 2311.4 mm
Rear - Scarifying Depth, Maximum
10.5 in 266.7 mm
Rear - Scarifier Shank Holder Spacing
10.5 in 266.7 mm
Mid, Straight - Working Width
71 in 1803.4 mm
Mid, Straight - Scarifier Shank Holder Spacing
4.4 in 111.8 mm
Mid, Straight - Scarifier Shank Holders
17 17
Mid, Straight - Scarifying Depth, Maximum
12.5 in 317.5 mm
Tandems
Sidewall Thickness - Inner
0.5 in 12.7 mm
Sidewall Thickness - Outer
0.6 in 15.3 mm
Drive Chain Pitch
1.8 in 45.8 mm
Wheel Axle Spacing
59.5 in 1511.3 mm
Tandem Oscillation - Front Up
15 degrees 15 degrees
Tandem Oscillation - Front Down
25 degrees 25 degrees
