Tandem Drive
Oscillating Welded Box Section
520 mm x 202 mm 520 mm x 202 mm
Side Wall Thickness: Inner
0.1 ft in 22 mm
Side Wall Thickness: Outer
0.1 ft in 19 mm
Wheel Axle Spacing
5.1 ft in 1525 mm
Tandem Oscillation
11u00b0 forward, 13 u00b0 reverse 11u00b0 forward, 13 u00b0 reverse
Drawbar
Drawbar Frame
210 x 25 mm 210 x 25 mm
Ripper
Ripper Penetration Force
20232.9 lb 90 kN
Ripper Pry Out Force
28685.7 lb 127.6 kN
Engine
Piston Displacement
408.3 cu in 6.7 L
Engine Model
KOMATSU SAA6D107E-1 KOMATSU SAA6D107E-1
Frame
Front Frame Structure - Height
1 ft in 300 mm
Front Frame Structure - Width
1 ft in 300 mm
Front Frame Structure - Thickness
0.1 ft in 14 mm
Engine
Engine Type
Water-cooled, 4 cycle, direct injection Water-cooled, 4 cycle, direct injection
Net Power
218.6 hp 163 kw
Gross Power
221.3 hp 165 kw
Air Cleaner
2-stage, dry-type 2-stage, dry-type
Max Torque
694.1 lb ft 941 Nm
Battery
2, low maintenance plus, 12 volt, 1146 cca 2, low maintenance plus, 12 volt, 1146 cca
Fan Speed
Max. 1500 rpm Max. 1500 rpm
Electrical
24 volt with 90 amp alternator 24 volt with 90 amp alternator
Aspiration
Turbocharged and air to air aftercooled Turbocharged and air to air aftercooled
Capacities
Fuel Tank - Diesel
109.9 gal 416 L
Cooling System
6.6 gal 24.9 L
Transmission
11.9 gal 45 L
Tandem Housing
15.1 gal 57 L
Hydraulic System
18.3 gal 69 L
Circle Reverse Housing
1.9 gal 7 L
Weights
Blade Down Pressure
19665.3 lb 8920 kg
Blade Pull
26091.8 lb 11835 kg
Operating Weight - On Rear Wheels
28990.8 lb 13150 kg
Total Operating Weight
40829.7 lb 18520 kg
Operating Weight - On Front Wheels
11841.1 lb 5371 kg
Front Axle
Wheel Lean
20 degrees 20 degrees
Oscillation - Total
32 degrees 32 degrees
Ground Clearance
2.1 ft in 620 mm
Front Axle Type
Solid bar construction welded steel sections Solid bar construction welded steel sections
Blade
Moldboard Side Shift: Right
2.7 ft in 820 mm
Hydraulic System
Standby Pressure
500 psi 3447.4 kPa
Blade
Moldboard Side Shift: Left
2.7 ft in 820 mm
Hydraulic System
Maximum System Pressure
3000 psi 20684.3 kPa
Blade
Maximum Shoulder Reach Outside Rear Tyres (Frame Straight): Right
6.6 ft in 2000 mm
Maximum Shoulder Reach Outside Rear Tyres (Frame Straight): Left
6.6 ft in 2000 mm
Hydraulic System
Output
52.9 gal/min 200 L/min
Blade
Maximum Lift Above Ground
1.6 ft in 480 mm
Maximum Cutting Depth
2.1 ft in 615 mm
Maximum Blade Angle
90 degrees 90 degrees
Blade Tip Angle
40 u00b0 forward, 5 u00b0 backward 40 u00b0 forward, 5 u00b0 backward
Circle Center Shift: Right
2 ft in 590 mm
Circle Center Shift: Left
1.9 ft in 550 mm
Blade Length
12.2 ft in 3.8 m
Moldboard
Moldboard Width
12.2 ft in 3710 mm
Moldboard Height
25.4 in 645 mm
Moldboard Thickness
0.9 in 22 mm
Cutting Edge
152 x 16 mm 152 x 16 mm
Arc Radius
1.1 ft in 329 mm
Circle